Introduction
All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with XINJE XD Series (Modbus TCP/IP). Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.
Supported Series: XINJE XD Series
Protocol: MODBUS TCP/IP
Website: http://www.xinje.com
HMI Settings
| Parameters | Recommended | Options | Notes |
|---|---|---|---|
| PLC type | XINJE XD Series MODBUS TCP/IP | ||
| PLC I/F | Ethernet | ||
| Port no. | 502 |
Device Address
| Bit/Word | Device type | Format | Range | Memo |
|---|---|---|---|---|
| B | M | DDDDD | 0 ~ 20479 | |
| B | X | Do | 0 ~ 77 | |
| B | X1xxxx | DDDo | 0 ~ 1777 | |
| B | X2xxxx | DDo | 0 ~ 177 | |
| B | X3xxxx | Do | 0 ~ 17 | |
| B | Y | Do | 0 ~ 77 | |
| B | Y1xxxx | DDDo | 0 ~ 1777 | |
| B | Y2xxxx | DDo | 0 ~ 177 | |
| B | Y3xxxx | Do | 0 ~ 17 | |
| B | S | DDDD | 0 ~ 7999 | |
| B | SM | DDDD | 0 ~ 4095 | |
| B | T | DDDD | 0 ~ 4095 | |
| B | C | DDDD | 0 ~ 4095 | |
| B | ET | DD | 0 ~ 39 | |
| B | SEM | DDD | 0 ~ 127 | |
| B | HM | DDDD | 0 ~ 6143 | |
| B | HS | DDD | 0 ~ 999 | |
| B | HT | DDDD | 0 ~ 1023 | |
| B | HC | DDDD | 0 ~ 1023 | |
| B | HSC | DD | 0 ~ 39 | |
| W | D | DDDDD | 0 ~ 20479 | |
| W | ID | DD | 0 ~ 99 | |
| W | ID1xxxx | DDDD | 0 ~ 1599 | |
| W | ID2xxxx | DDD | 0 ~ 199 | |
| W | ID3xxxx | DD | 0 ~ 99 | |
| W | QD | DD | 0 ~ 99 | |
| W | QD1xxxx | DDDD | 0 ~ 1599 | |
| W | QD2xxxx | DDD | 0 ~ 199 | |
| W | QD3xxxx | DD | 0 ~ 99 | |
| W | SD | DDDD | 0 ~ 4095 | |
| W | TD | DDDD | 0 ~ 4095 | |
| W | CD | DDDD | 0 ~ 4095 | |
| W | ETD | DD | 0 ~ 39 | |
| W | HD | DDDD | 0 ~ 6143 | |
| W | HSD | DDDD | 0 ~ 1023 | |
| W | HTD | DDDD | 0 ~ 1023 | |
| W | HCD | DDDD | 0 ~ 1023 | |
| W | HSCD | DD | 0 ~ 39 | |
| W | FD | DDDD | 0 ~ 8191 | |
| W | SFD | DDDD | 0 ~ 4095 | |
| W | FS | DDD | 0 ~ 255 | |
| W | DM | DDDD | 0 ~ 1279 | Read only |
| W | DX | D | 0 ~ 7 | Read only |
| W | DX1xxx | DDD | 0 ~ 177 | Read only |
| W | DX2xxx | DD | 0 ~ 17 | Read only |
| W | DX3xxx | D | 0 ~ 7 | Read only |
| W | DY | D | 0 ~ 7 | Read only |
| W | DY1xxx | DDD | 0 ~ 177 | Read only |
| W | DY2xxx | DD | 0 ~ 17 | Read only |
| W | DY3xxx | D | 0 ~ 7 | Read only |
| W | DS | DDD | 0 ~ 499 | Read only |
| W | DSM | DDD | 0 ~ 255 | Read only |
| W | DT | DDD | 0 ~ 255 | Read only |
| W | DC | DDD | 0 ~ 255 | Read only |
| W | DET | D | 0 ~ 1 | Read only |
| W | DSEM | D | 0 ~ 7 | Read only |
| W | DHM | DDD | 0 ~ 383 | Read only |
| W | DHS | DD | 0 ~ 61 | Read only |
| W | DHT | DD | 0 ~ 63 | Read only |
| W | DHC | DD | 0 ~ 63 | Read only |
| W | DHSC | D | 0 ~ 1 | Read only |
NOTE: This driver uses the Modbus protocol. Because of the mapping address, it cannot support the complete PLC address range.
Wiring Diagram
NOTE: Connect the HMI to the XINJE XD Series PLC using a standard straight-through Ethernet cable.
The diagram below shows the Ethernet cable wiring.
