Introduction
All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with Toshiba T Series. Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.
Supported Series: Toshiba T series, S2E
Website: http://www.tic.toshiba.com
HMI Settings
| Parameters | Recommended | Options | Notes |
|---|---|---|---|
| PLC type | TOSHIBA T Series | ||
| PLC I/F | RS232 | RS232/RS485 | In accordance with PLC port |
| Baud rate | 9600 | 9600, 19200, 38400, 57600, 115200 | |
| Data bits | 8 | 7, 8 | |
| Parity | Odd | Even, Odd, None | |
| Stop bits | 1 | 1, 2 | |
| PLC sta. no. | 0 | 0–255 | Must be same as the PLC setting |
| Online simulator | YES | ||
| Extend address mode | YES |
PLC Settings
| Parameter | Notes |
|---|---|
| Communication mode | Must set PLC node ID |
Device Address
| Bit/Word | Device | Format | Range | Memo |
|---|---|---|---|---|
| B | X | DDDDh | 0 ~ 4095 | Input Bit |
| B | Y | DDDDh | 0 ~ 4095 | Output Bit |
| B | R | DDDDh | 0 ~ 8191 | Auxiliary Bit |
| B | S | DDDDh | 0 ~ 4095 | Special Bit |
| B | L | DDDDh | 0 ~ 4095 | |
| B | Z | DDDDh | 0 ~ 8191 | |
| W | T | DDD | 0 ~ 999 | Timer Register |
| W | C | DDD | 0 ~ 511 | Counter Register |
| W | D | DDDD | 0 ~ 8191 | Data Memory |
| W | SW | DDD | 0 ~ 255 | Special Register |
| W | XW | DDD | 0 ~ 255 | Input Register |
| W | YW | DDD | 0 ~ 255 | Output Register |
| W | RW | DDD | 0 ~ 999 | Auxiliary Register |
| W | LW | DDD | 0 ~ 255 | |
| W | W | DDDD | 0 ~ 1023 | |
| W | F | DDDD | 0 ~ 8191 |
Wiring Diagrams
NOTE: The serial port pin assignments may vary between HMI models.
Diagram 1: RS-232 (8P Mini-DIN)
The following is the view from the soldering point of the connector.
| HMI | Direction | PLC |
|---|---|---|
| Pin assignments | RS232 8P Mini-DIN | |
| Rx | ↔ (bidirectional) | 6 TX |
| Tx | ↔ (bidirectional) | 8 RX |
| GND | ↔ (bidirectional) | 5 GND |
| ↕︎ (tie) | 4 7 |
Diagram 2: RS-232 (9P D-Sub Male)
| HMI | Direction | PLC |
|---|---|---|
| Pin assignments | RS232 9P D-Sub Male | |
| Rx | ↔ (bidirectional) | 3 TX |
| Tx | ↔ (bidirectional) | 2 RX |
| GND | ↔ (bidirectional) | 5 GND |
| ↕︎ (tie) | 7 8 |
Diagram 3: RS-485 4W (15P D-Sub Male)
| HMI | Direction | PLC |
|---|---|---|
| Pin assignments | RS485 4W 15P D-Sub Male | |
| Rx− | ↔ (bidirectional) | 11 TXD− |
| RX+ | ↔ (bidirectional) | 3 TXD+ |
| Tx− | ↔ (bidirectional) | 10 RXD− |
| Tx+ | ↔ (bidirectional) | 2 RXD+ |
| GND | ↔ (bidirectional) | 7 GND |
| ↕︎ (tie) | 5 4 | |
| ↕︎ (tie) | 13 12 |