Connection Parameters Needed for HMI/cMT Products to Communicate with JTEKT Toyopuc PCk06 using EBPro (EasyBuilder Pro)

Introduction

All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with JTEKT Toyopuc PCk06. Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.

Supported Series: JTEKT Toyopuc PCk06

Website: http://www.jtekt.co.jp/

HMI Settings

Parameters	Recommended	Options
PLC type	JTEKT Toyopuc PCk06
PLC I/F	RS232	RS232
Baud rate	9600	9600, 19200, 38400
Data bits	8
Parity	Odd	Odd, Even, None
Stop bits	1	1, 2
PLC sta. no.	N/A

Device Address

Bit/Word	Device type	Format	Range
B	K_Bit	Hh	0 ~ ff
B	1K_Bit	Hh	0 ~ ff
B	V_Bit	Hh	0 ~ ff
B	T_Bit	Hh	0 ~ ff
B	1C_Bit	Hh	0 ~ 7f
B	L_Bit	HHh	0 ~ 7ff
B	X_Bit	Hh	0 ~ ff
B	1X_Bit	Hh	0 ~ ff
B	4Y_Bit	Hh	0 ~ ff
B	5Y_Bit	Hh	0 ~ ff
B	M_Bit	Hh	0 ~ ff
B	1M_Bit	Hh	0 ~ ff
B	4M_Bit	Hh	0 ~ ff
B	S_Bit	HHHh	0 ~ 3fff
B	N_Bit	HHh	0 ~ fff
B	1N_Bit	HHh	0 ~ 7ff
B	D_Bit	HHHh	0 ~ cfff
B	1D_Bit	HHHh	0 ~ ffff
W	K	H	0 ~ f
W	1K	H	0 ~ f
W	V	H	0 ~ f
W	T	H	0 ~ f
W	1C	H	0 ~ 7
W	L	HH	0 ~ 7f
W	X	H	0 ~ f
W	1X	H	0 ~ f
W	4Y	H	0 ~ f
W	5Y	H	0 ~ f
W	M	H	0 ~ f
W	1M	H	0 ~ f
W	4M	H	0 ~ f
W	S	HHH	0 ~ 3ff
W	N	HH	0 ~ ff
W	1N	HH	0 ~ 7f
W	D	HHH	0 ~ cff
W	1D	HHH	0 ~ fff

Wiring Diagrams

NOTE: The serial port pin assignments may vary between HMI models.

RS-232 (CPU Port1)

Connector view from soldering point showing RJ12 6-pin layout for JTEKT Toyopuc PCk06 CPU Port1 RS-232 connection.

The view from the soldering point of a connector.

HMI	Direction	PLC
Pin assignments		RJ12 RS232
Rx	↔ (bidirectional)	4
Tx	↔ (bidirectional)	3
GND	↔ (bidirectional)	1

RS-232 (CPU Port2)

Connector view from soldering point showing RJ12 6-pin layout for JTEKT Toyopuc PCk06 CPU Port2 RS-232 connection.

The view from the soldering point of a connector.

HMI	Direction	PLC
Pin assignments		RS232 15P D-SUB Male
Rx	↔ (bidirectional)	2
Tx	↔ (bidirectional)	3
GND	↔ (bidirectional)	7