Connection Parameters Needed for HMI/cMT Products to Communicate with LS Electric XEC Cnet using EBPro (EasyBuilder Pro)

Introduction

All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with LS Electric XEC Cnet. Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.

Supported Series: LS XGB Series XEC CPU with communication module XGL-CH2A

Website: http://www.lgis.com/

HMI Settings

Parameters	Recommended	Options
PLC type	LS XEC Cnet
PLC I/F	RS232	RS232/RS485
Baud rate	115200	9600 ~ 115200
Data bits	8	7, 8
Parity	None	Even, Odd, None
Stop bits	1	1, 2
PLC sta. no.	0	0 ~ 32

Device Addresses

Bit/Word	Device Type	Format	Range	Memo
B	`AW_Bit`	`DDDDDDh`	0 ~ 262143f	Automatic variable bit
B	`IW_Bit`	`DDD.DD.Dh`	0 ~ 127.15.3f	Input device bit
B	`QW_Bit`	`DDD.DD.Dh`	0 ~ 127.15.3f	Output device bit
B	`MW_Bit`	`DDDDDDDh`	0 ~ 1048575f	Direct variable bit
B	`RW_Bit`	`DDDDDh`	0 ~ 32767f	Direct variable bit
B	`WW_Bit`	`DDDDDh`	0 ~ 65535f	Direct variable bit
B	`FW_Bit`	`DDDDh`	0 ~ 2047f	System flag bit
B	`KW_Bit`	`DDDDh`	0 ~ 8399f	Built-in special flag bit
B	`LW_Bit`	`DDDDDh`	0 ~ 11263f	High speed link flag bit
B	`NW_Bit`	`DDDDDh`	0 ~ 25087f	P2P flag bit
B	`UW_Bit`	`DD.DD.DDh`	0 ~ 31.15.31f	Analog flag bit
B	`AX`	`DDDDDDD`	0 ~ 4194303
B	`IX`	`DDD.DD.DD`	0 ~ 127.15.63
B	`QX`	`DDD.DD.DD`	0 ~ 127.15.63
B	`MX`	`DDDDDDDD`	0 ~ 16777199
B	`RX`	`DDDDDD`	0 ~ 524287
B	`WX`	`DDDDDDD`	0 ~ 1048575
B	`FX`	`DDDDD`	0 ~ 32767
B	`KX`	`DDDDDD`	0 ~ 134399
B	`LX`	`DDDDDDD`	0 ~ 1880223
B	`NX`	`DDDDDD`	0 ~ 401407
B	`UX`	`DD.DD.DDD`	0 ~ 31.15.511
W	`AW`	`DDDDDD`	0 ~ 262143	Automatic variable
W	`IW`	`DDD.DD.D`	0 ~ 127.15.3	Input device
W	`QW`	`DDD.DD.D`	0 ~ 127.15.3	Output device
W	`MW`	`DDDDDDD`	0 ~ 1048575	Direct variable
W	`RW`	`DDDDD`	0 ~ 32767	Direct variable
W	`WW`	`DDDDD`	0 ~ 65535	Direct variable
W	`FW`	`DDDD`	0 ~ 2047	System flag
W	`KW`	`DDDD`	0 ~ 8399	Built-in special flag
W	`LW`	`DDDDD`	0 ~ 11263	High speed link flag
W	`NW`	`DDDDD`	0 ~ 25087	P2P flag
W	`UW`	`DD.DD.DD`	0 ~ 31.15.31	Analog flag
DW	`MD`	`DDDDDD`	0 ~ 524287
Byte	`MB`	`DDDDDDD`	0 ~ 2097151
LW	`ML`	`DDDDDD`	0 ~ 262143

Wiring Diagrams

NOTE: The serial port pin assignments may vary between HMI models.

RS232

HMI	Direction	PLC
Pin assignments		RS232 Terminal
Rx	↔ (bidirectional)	Tx
Tx	↔ (bidirectional)	Rx
GND	↔ (bidirectional)	SG

RS-485 2W

HMI	Direction	PLC
Pin assignments		RS485 2W Terminal
Data-	↔ (bidirectional)	485-
Data+	↔ (bidirectional)	485+
GND	↔ (bidirectional)	GND