Introduction
All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with MEGMEET MC Series. Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.
Supported Series: MEGMEET MC Series (Modbus RTU Protocol and Modbus TCP/IP
Protocol: Modbus RTU / Modbus TCP/IP
HMI Settings
| Parameters | Recommended | Options | Notes |
|---|---|---|---|
| PLC type | MEGMEET MC Series | ||
| PLC I/F | RS232/Ethernet | ||
| Baud rate | 9600 | 9600, 19200, 115200 | |
| Data bits | 8 | 8 | |
| Parity | Even | Even, Odd, None | |
| Stop bits | 1 | 1 or 2 | |
| Port no. | 502 | ||
| PLC sta. no. | 0 | 0–255 |
PLC Settings
| Parameter | Value |
|---|---|
| Communication mode | Modbus RTU protocol / Modbus TCP/IP protocol |
Device Address
| Bit/Word | Device type | Format | Range | Memo |
|---|---|---|---|---|
| B | X |
OOO | 0 ~ 377 | 1200~01455 0000~0255 |
| B | Y |
OOO | 0 ~ 377 | 0000~0255 |
| B | M |
DDDDD | 0 ~ 10239 | 2000~2047 12000~20191 |
| B | SM |
DDD | 0 ~ 511 | 4400~4655 30000~30255 |
| B | S |
DDDD | 0 ~ 4095 | 6000~7023 31000~34071 |
| B | T_Bit |
DDD | 0 ~ 511 | 8000~8255 |
| B | C_Bit |
DDD | 0 ~ 306 | 9200~9455 10000~10050 |
| B | D_Bit |
DDDDdd | 0 ~ 799915 | |
| B | R_Bit |
DDDDDdd | 0 ~ 3276715 | |
| W | D |
DDDD | 0 ~ 7999 | 0000~7999 |
| DW | D_Double |
DDDD | 0 ~ 7998 | 0000~7999 |
| W | SD |
DDD | 0 ~ 511 | 8000~8255 12000~12255 |
| DW | SD_Double |
DDD | 0 ~ 510 | 8000~8255 12000~12255 |
| W | Z |
DD | 0 ~ 15 | 8500~8515 |
| W | T |
DDD | 0 ~ 511 | 9000~9255 11000~11255 |
| W | C |
DDD | 0 ~ 199 | 9500~9699 |
| DW | C_Double |
DDD | 200 ~ 306 | 9700~10101 |
| W | R |
DDDDD | 0 ~ 32767 | 13000~45767 |
| DW | R_Double |
DDDDD | 0 ~ 32766 | 13000~45767 |
Wiring Diagram
NOTE: The serial port pin assignments may vary between HMI models.
RS-232
| HMI | Direction | PLC |
|---|---|---|
| Pin assignments | MC Series COM1 terminal | |
| Rx | ↔ (bidirectional) | TXD |
| Tx | ↔ (bidirectional) | RXD |
| GND | ↔ (bidirectional) | GND |