Connection Parameters Needed for HMI/cMT Products to Communicate with Chuang Hong DL/T645 using EBPro (EasyBuilder Pro)

Introduction

All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with Chuang Hong DL/T645. Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.

HMI Setting

Parameters	Recommended	Options	Notes
PLC type	DL/T645 CHUANG HONG
PLC I/F	RS485 2W
Baud rate	9600
Data bits	8
Parity	Even
Stop bits	1
PLC sta. no.	1

Device Address

Bit/Word	Device type	Format	Range
W	B621	D	0 ~ 1
W	B622	D	0 ~ 1
W	B623	D	0 ~ 1
W	zero phase	D	0 ~ 1
W	B611	D	0 ~ 1
W	B612	D	0 ~ 1
W	B613	D	0 ~ 1
W	B631	D	0 ~ 1
W	B632	D	0 ~ 1
W	B633	D	0 ~ 1
W	B630	D	0 ~ 1
W	B641	D	0 ~ 1
W	B642	D	0 ~ 1
W	B643	D	0 ~ 1
W	B640	D	0 ~ 1
W	A-apparentT	D	0 ~ 1
W	B-apparentT	D	0 ~ 1
W	C-apparentT	D	0 ~ 1
W	T-apparentT	D	0 ~ 1
W	B650	D	0 ~ 1
W	B651	D	0 ~ 1
W	B652	D	0 ~ 1
W	B653	D	0 ~ 1
W	9010	D	0 ~ 1
W	9020	D	0 ~ 1
W	9110	D	0 ~ 1
W	9120	D	0 ~ 1
W	9130	D	0 ~ 1
W	9140	D	0 ~ 1
W	9150	D	0 ~ 1
W	9160	D	0 ~ 1
W	9410	D	0 ~ 1
W	9420	D	0 ~ 1
W	9510	D	0 ~ 1
W	9520	D	0 ~ 1
W	9530	D	0 ~ 1
W	9540	D	0 ~ 1
W	9550	D	0 ~ 1
W	9560	D	0 ~ 1
W	9810	D	0 ~ 1
W	9820	D	0 ~ 1
W	9910	D	0 ~ 1
W	9920	D	0 ~ 1
W	9930	D	0 ~ 1
W	9940	D	0 ~ 1
W	9950	D	0 ~ 1
W	9960	D	0 ~ 1
W	A010	D	0 ~ 1
W	A020	D	0 ~ 1
W	A110	D	0 ~ 1
W	A120	D	0 ~ 1
W	A130	D	0 ~ 1
W	A140	D	0 ~ 1
W	A150	D	0 ~ 1
W	A160	D	0 ~ 1
W	A410	D	0 ~ 1
W	A420	D	0 ~ 1
W	A510	D	0 ~ 1
W	A520	D	0 ~ 1
W	A530	D	0 ~ 1
W	A540	D	0 ~ 1
W	A550	D	0 ~ 1
W	A560	D	0 ~ 1
W	A810	D	0 ~ 1
W	A820	D	0 ~ 1
W	A910	D	0 ~ 1
W	A920	D	0 ~ 1
W	A930	D	0 ~ 1
W	A940	D	0 ~ 1
W	A950	D	0 ~ 1
W	A960	D	0 ~ 1
W	B010	D	0 ~ 1
W	B020	D	0 ~ 1
W	B110	D	0 ~ 1
W	B120	D	0 ~ 1
W	B130	D	0 ~ 1
W	B140	D	0 ~ 1
W	B150	D	0 ~ 1
W	B160	D	0 ~ 1
W	B410	D	0 ~ 1
W	B420	D	0 ~ 1
W	B510	D	0 ~ 1
W	B520	D	0 ~ 1
W	B530	D	0 ~ 1
W	B540	D	0 ~ 1
W	B550	D	0 ~ 1
W	B560	D	0 ~ 1
W	B810	D	0 ~ 1
W	B820	D	0 ~ 1
W	B910	D	0 ~ 1
W	B920	D	0 ~ 1
W	B930	D	0 ~ 1
W	B940	D	0 ~ 1
W	B950	D	0 ~ 1
W	B960	D	0 ~ 1
W	B210	D	0 ~ 1
W	B211	D	0 ~ 1
W	B212	D	0 ~ 1
W	B213	D	0 ~ 1
W	B214	D	0 ~ 1
W	B310	D	0 ~ 1
W	B311	D	0 ~ 1
W	B312	D	0 ~ 1
W	B313	D	0 ~ 1
W	B320	D	0 ~ 1
W	B321	D	0 ~ 1
W	B322	D	0 ~ 1
W	B323	D	0 ~ 1
W	B330	D	0 ~ 1
W	B331	D	0 ~ 1
W	B332	D	0 ~ 1
W	B333	D	0 ~ 1
W	B340	D	0 ~ 1
W	B341	D	0 ~ 1
W	B342	D	0 ~ 1
W	B343	D	0 ~ 1
W	C010	D	0 ~ 1
W	C011	D	0 ~ 1
W	C020	D	0 ~ 1
W	C021	D	0 ~ 1
W	C022	D	0 ~ 1
W	C030	D	0 ~ 1
W	C031	D	0 ~ 1
W	C032	D	0 ~ 1
W	C033	D	0 ~ 1
W	C034	D	0 ~ 1
W	C111	D	0 ~ 1
W	C112	D	0 ~ 1
W	C113	D	0 ~ 1
W	C114	D	0 ~ 1
W	C115	D	0 ~ 1
W	C116	D	0 ~ 1
W	C117	D	0 ~ 1
W	C118	D	0 ~ 1
W	C119	D	0 ~ 1
W	C11A	D	0 ~ 1
W	C211	D	0 ~ 1
W	C212	D	0 ~ 1
W	C310	D	0 ~ 1
W	C311	D	0 ~ 1
W	C312	D	0 ~ 1
W	C313	D	0 ~ 1
W	C314	D	0 ~ 1
W	C320	D	0 ~ 1
W	C321	D	0 ~ 1
W	C322	D	0 ~ 1
W	C330	D	0 ~ 1
W	C331	D	0 ~ 1
W	C332	D	0 ~ 1
W	C340	D	0 ~ 1
W	C341	D	0 ~ 1
W	C342	D	0 ~ 1
W	C3A0	D	0 ~ 1
W	C3A1	D	0 ~ 1
W	C3A2	D	0 ~ 1
W	C410	D	0 ~ 1
W	C411	D	0 ~ 1
W	C41E	D	0 ~ 1
W	C510	D	0 ~ 1
W	C511	D	0 ~ 1
W	B634	D	0 ~ 1
W	B635	D	0 ~ 1

Wiring Diagram

NOTE: The serial port pin assignments may vary between HMI models.

RS-485 2W

HMI	Direction	PLC
Pin assignments		RS485 2W Terminal
Data-	↔ (bidirectional)	13 RS485B1
Data+	↔ (bidirectional)	12 RS485A1
GND	↔ (bidirectional)	GND