Getting Started
Unpacking the Unit
Carefully unpack the Industrial Monitor. Check all material in the container against the packing list. Maple Systems will not accept responsibility for shortages against the packing list unless notified within 30 days. The equipment and accessories were inspected and tested by Maple Systems before shipment.
Examine the equipment carefully; if any shipping damage is evident, notify the carrier immediately. Maple Systems is not responsible for claim negotiations with the carrier.
Save the shipping container and packing material in case the equipment needs to be stored, returned to Maple Systems, or transported for any reason.
| Packing List: AEx-100 Series |
|---|
| AEx-100 Series Industrial Projected Capacitive Touch Monitor |
| DC Power Cable (M12 to leads – 5’ and 15’) |
| OSD Controller (with 10’ cable extension) |
| I/O Cables: USB 2.0 Cable (M12 to 2x USB 2.0 Type A, 10’) VGA Cable (M12 to VGA, 10’) |
| Warranty Statement Insert |
Safety Precautions
Please observe the following precautions when installing the AEx-100 Series Industrial Monitor. Failure to comply with these restrictions could result in loss of life, serious personal injury, or equipment damage.
Warning: Disconnect this equipment from any power before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth.
Warning: Keep this equipment away from humidity.
Warning: Before applying power the unit make sure the voltage of the power source is within the input voltage rating of the unit.
Operating the unit outside of this voltage specification can damage the unit and void your Warranty.
Warning: Never open the equipment and do not operate equipment with its rear cover removed- there are dangerous high voltages present inside. For safety reasons, the equipment should be opened only by a qualified service technician.
Warning: This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction’s manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Warning: If any of the following situations arise, get the equipment checked by qualified service personnel.
- The power cord or plug is damaged.
- Liquid has penetrated into the equipment.
- The equipment has been exposed to moisture.
- The equipment does not work well, or you cannot get it to work according to this operations manual.
- The equipment has been dropped and damaged.
- The equipment has obvious signs of breakage.
Warning: Risk of explosion if the battery is replaced with an incorrect type.
Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.
Warning: Do not leave this equipment in an uncontrolled environment where the storage temperature is below -30°C (-22°F) or above 70°C (158°F). It may damage the equipment.
Overview
The AEx-100 Series Industrial Projected Capacitive Touch Monitor is available in 15.0” and 19.0” screen sizes. The AEx-100 Series monitors are constructed of 316 Stainless Steel and are ideal for use in hazardous locations thanks to their CSA Class I, Division 2, Class II Division 2, Class III, and ATEX/IECEx Zone 2, Zone 22 certifications.
The AEx-100 Series Monitors are IP66 rated and can operate in extended temperature (-20~60°C) environments, as well as locations where high brightness is a requirement. AEx-100 Series monitors feature high brightness, sunlight readable displays (1000 Nits) via their optically bonded construction.
The AEx-100 Series feature Projected Capacitive Touch Screens, which allow for a more natural, intuitive user touch experience compared to traditional analog-resistive touch screen terminals. Benefits of projected capacitive touchscreens include multi-touch response (pinch and zoom functionality) and personal tablet-like operation. Finally, projected capacitive touchscreens do not require calibration
I/O Ports and Cables
The below section provides information on the I/O connectors and cables for your AEx-100 Series Monitor. All connections at the monitor are M12 style; M12 connections are durable, rugged, and carry an IP67 rating against dust and water intrusion. AEx- Series Monitors come with one of each of the below cables (unless specified otherwise).
Power Input (9-36 VDC)
Your AEx-100 Series Monitor comes with both a 1M (~3’) cable (7431-0134) as well as a 5M (~15’) DC power input cable (7431-0129). 3’ DC power cable drawing shown above.
VGA
VGA cable allows for connection to your PC, enabling the AEx-100 Series monitor to display the signals from your PC VGA output device.
USB (Touch Control Operation)
To enable the AEx-100 Series’ touch functionality, this USB cable must be plugged into a USB 2.0 (or better) port of your PC.
OSD (On-Screen Display) Controller
The On-Screen Display Controller is used to adjust the operational parameters of the OSD menu.
On-Screen Display (OSD) Operation
Your AEx-100 Series Monitor has Power and On-Screen Display (OSD) buttons located on the On-Screen Display Controller. If the monitor is powered on, but does not have an active connection to a computer, the power indicator will illuminate RED. When there is an active PC connection, the power indicator will illuminate GREEN.
The table below shows the buttons and their respective operations.
| Button | Function with OSD menu active | Function with OSD menu inactive |
|---|---|---|
 | Turns the power ON or OFF | Turns the power ON or OFF |
 | This button scrolls left through submenus. In a submenu, this button increases the selected parameter value. | Adjust brightness value of the monitor downward (decrease display brightness) |
 | Scrolls right through submenus. In a submenu, this button decreases the selected parameter value. | Adjust brightness value of the monitor upward (increase display brightness) |
 | If an OSD menu parameter is highlighted, pressing this button will select the highlighted menu item/icon and enter the parameter adjustment submenu. If there is no highlighted parameter, this button is used to exit the On-Screen Display menu. | Enters the On-Screen Display menu. |
 | Automatically Adjusts the Monitor’s Image settings | Opens the input menu to allow change of display input connection. |
OSD Menu Parameters and Options
Main Menu
This is the initial OSD menu that shows up when the OSD Menu button is pressed.
Picture Menu
In the Picture menu, the following parameters can be adjusted:
- Backlight
- Brightness
- Contrast
- Sharpness
- (Exit to Main Menu)
Display Menu
In the Display menu, the following parameters can be adjusted:
- Auto Adjustment
- H Position (Horizontal)
- V Position (Vertical)
- Pixel Clock
- Phase
- (Exit to Main Menu)
Color Menu
In the Color menu, the following parameters can be adjusted:
- Gamma
- Color Temperature
- Color Effect
- (Exit to Main Menu)
Advance Menu
In the Advance menu, the following parameter can be adjusted:
- Aspect Ratio
- (Exit to Main Menu)
Input Menu
In the Input menu, the following parameters are shown:
- Auto Select
- VGA
- DP (DisplayPort)
- DVI
- (Exit to Main Menu)
Note: AEx-100 Series Monitors use VGA Input only.
Audio Menu
In the Audio menu, the following parameters are shown:
- Volume
- Mute
- (Exit to Main Menu)
Other Menu
In the Other menu, the following parameters can be adjusted:
- Reset
- Menu Time
- OSD H Position
- OSD V Position
- Language
- Transparency
- Rotate
- (Exit to Main Menu)
Information Menu
The Information menu provides information of the current PC connection. Selecting Exit will exit the OSD menu.
Mounting Options
The AEx-100 Series offer VESA mounting as an option. VESA 100 x 100mm threaded inserts are located on the rear of the unit. Use M4 threaded mounting screws included with the VESA mounting hardware to mount the AEx-100 Series as illustrated in the figure below.
Use VESA mounting hardware suitable for your intended application; Maple Systems is not responsible for damage to unit, mounting surface, or to other components caused by improper mounting.
PC Connection
You will need to connect your AEx-100 Series unit to a PC. Use the included VGA and USB Cables to connect your monitor and PC. When connected to a computer running a Windows® 8.x or 10 Operating System, there are no additional drivers required for operation. Your AEx-100 Series monitor uses standard Windows® HID (Human Interface Device) Drivers.
Connecting to a PC
Follow these simple steps to connect your AEx-100 Series Monitor to a PC.
Instructions: Connecting to a PC
Power Off All Equipment
Be sure all equipment is powered off.Connect VGA Cable
Connect the M12 connector of the VGA cable to the input connector on the monitor, the other end to the VGA connector on your PC.Connect USB Touch Cable (Optional)
If touch operation from the monitor is desired, plug the “rectangular end” of the included USB cable to a USB port of your PC.The AEx-100 Series can be used as a simple, non touch monitor if desired. Simply do not connect the USB touch cable if you do not want touch functionality with your AEx-100 Series.Connect Power Cable
Connect one end of your power cable to the power connector on the monitor, and the other end to the VDC output of your power supply.Power up the PC and AEx-100 Series
Apply power to your monitor and PC. Your monitor should now be displaying your PC desktop.