Connection Parameters Needed for HMI/cMT Products to Communicate with CO-TRUST CTH300-H (Ethernet) using EBPro (EasyBuilder Pro)

Introduction

All Maple Systems HMIs programmed with EBPro (EasyBuilder Pro), including every cMT X Series and cMT Series model, are compatible with CO-TRUST CTH300-H (Ethernet). Configure your Controller and HMI/cMT with the following parameters to establish reliable communication.

Supported Series: CO-TRUST CTH300-H35

Website: http://en.co-trust.com/

HMI Setting

Parameters	Recommended	Notes
PLC type	CO-TRUST CTH300-H (Ethernet)	Use UDP
PLC I/F	Ethernet
Port no.	1024
PLC sta. no.	0

Device Address

Bit/Word	Device type	Format	Range	Memo
B	`I`	DDDDo	0 ~ 40957	Input (I)
B	`Q`	DDDDo	0 ~ 40957	Output (O)
B	`M`	DDDDo	0 ~ 40957	Bit Memory
B	`VW_Bit`	DDDDDo	0 ~ 655347	V Memory Bit Address
B	`S`	DDDDo	0 ~ 40957	SCR
B	`SM`	DDDDo	0 ~ 40957	Special Memory
B	`T_Bit`	DDDD	0 ~ 1023	Timer
B	`C_Bit`	DDDD	0 ~ 1023	Counter
B	`DBnBit`	FFFDDDDDo	0 ~ 255655357
Byte	`VB`	DDDDD	0 ~ 65535
W	`VW`	DDDDD	0 ~ 65534	V Memory
W	`VW_Odd`	DDDDD	0 ~ 65534	V Memory
W	`VW_String`	DDDDD	0 ~ 65534	String
W	`VW_String_Odd`	DDDDD	0 ~ 65532	String
DW	`VD`	DDDDD	0 ~ 65532	V Memory Double
DW	`VD_Odd`	DDDDD	0 ~ 65532	V Memory Double
DW	`VD_String`	DDDDD	0 ~ 65532	String
DW	`VD_String_Odd`	DDDDD	0 ~ 65532	String
Byte	`MB`	DDDDD	0 ~ 10239	Byte Memory
W	`MW`	DDDDD	0 ~ 10239	Word Memory
W	`MW_Odd`	DDDDD	0 ~ 10239	Word Memory
DW	`MD`	DDDDD	0 ~ 10239	Word Memory
Byte	`SB`	DDDDD	0 ~ 10239	SCR
W	`SW`	DDDDD	0 ~ 10239	SCR
DW	`SD`	DDDDD	0 ~ 10239	SCR
Byte	`SMB`	DDDDD	0 ~ 10239	Special Memory
W	`SMW`	DDDDD	0 ~ 10239	Special Memory
DW	`SMD`	DDDDD	0 ~ 10239	Special Memory
W	`T`	DDD	0 ~ 1023	Timer
W	`C`	DDD	0 ~ 1023	Counter
Byte	`DBBn`	FFFDDDDD	0 ~ 25565535
W	`DBn`	FFFDDDDD	0 ~ 25565535
DW	`DBDn`	FFFDDDDD	0 ~ 25565535
D	`DBn_STRINGCHAR`	FFFDDDDD	0 ~ 25565535

NOTE: Double Word and floating point value must use VD device type.

Wiring Diagram

The diagram below shows the Ethernet cable wiring.